The Science of Magneto Hydro
Dynamics
The Micro Chip of the Water Industry!
Invented by Justin Sharaf
Endorsed by Applied BioPhysics Foundation
http://www.RhinoEd.org
Page 1
Page 3
Cooling Towers
Boilers:
Boilers undergo extreme changes in
water temperatures. Cold incoming water is brought to a boil or even converted
to steam very rapidly. This cycle is maintained twenty-four hours a day for
months on end. This continuous action causes both suspended and dissolved solids
in the water to plate out inside boiler tubes and pipes. The addition of
Chemicals aggravates the problem, because Chemicals react differently with
different substances in the water as well as with the metallurgical content of
the pipes, setting off chain reactions before vaporizing. Then the vapors
migrate with the water and steam. Consequently, while at one stage of the cycle,
the water may be rendered acceptable for boiler use, down the pipelines, the
vaporized Chemicals migrating with the turbulent boiling water and the steam,
begin to react with other metals and substances inside the flow paths, which are
also experiencing fluctuating temperatures.
Thus begins another Chemical chain
reaction, often leading to corrosion inside the heat exchangers and pipelines,
especially the elbows, joints, distribution points, Condensate return paths,
Condensate and holding tanks. The addition of Fresh make up water only brings in
more additives with it to further aggravate the problem. Consequently,
while a chemical may solve an immediate problem at the source, it causes
multifarious problems down the line and in pipes far from the boilers. The big
question every Boiler owner or operator should ask is:
"If the Chemicals did their job,
then why do we have calcium and other build-ups in our boilers?" And, "why is
there corrosion inside our pipelines where only steam is passing?" Obviously,
CHEMICALS have serious shortcomings!
We always recommend, that in the
case of Boilers, we must take a very serious look at the composition of the
incoming water and take steps to reduce as many Suspended and Dissolved Solids
from the water before it goes into the Boilers. Our ECOBEAM XL SYSTEMS will play
a crucial role in this effort. After this has been done, it is recommended to
treat all of the circulating water systems, condensate return and fresh-water
makeup lines, with the ECOBEAM XL SYSTEM. Depending on the composition of
the source water, the use of all chemicals will be eliminated, or at least
dramatically reduced.
Oil Lines:
The ECOBEAM XL SERIES of MHD units
should be used to control paraffin, salt, and scale in oil lines. But this
undertaking should only be attempted after consultation with a representative of
ECOTECH and after the necessary Test Protocols have been carefully conducted and
examined. The Magneto-Hydrodynamic Technology Treatment, if applied correctly,
will greatly enhance the flow of the oil and will hold most dissolved and
suspended solids in suspension.
OIL FIELD
APPLICATIONS
Steam Compressors:
The application of the ECOBEAM XL
SYSTEMS on water lines to the compressor, and, to and from the Cooling Towers
will not only prevent scale buildup in the compressors and piping, but
will also gradually remove all existing scale already deposited in them.
This having been done, there will be no more need for a water softener or
chemicals to control scale and corrosion.
Water Injection:
An EOR, (Enhanced Oil Recovery) a
typical system includes: a pump (to force water into the oil well), a tank
(Q-cell) (to add coagulant for oil separation), and a diatomaceous earth filter.
The installation of the ECOBEAM XL SYSTEMS should be at carefully selected
locations to treat oil and water going to the tanks, to treat the Q-cell-ahead
of D.E. filters, and the water before re-entry into the ground. This
application will help control H2S, salt and scale deposits, and decrease
turbidity after the filters.
Oil Pipe Lines:
The installation of the ECOBEAM XL
SYSTEMS at carefully selected locations will assist in preventing paraffin,
salt, and scale buildup in the lines. Depending on the composition of the oil,
the need for chemicals will be dramatically reduced or may even be eliminated.
Paraffin is non polar, a totally saturated hydrocarbon. As the molecular weight
of the fuel oil increases, the melting point of paraffin increases. Water and
hydrocarbons will not mix. It should be understood that there is 60 to 94 %
water, along with oil, in most oil producing wells.
Salt Water
The Installation of the ECOBEAM XL
SYSTEMS will prevent scale and corrosion buildup in the salt water lines,
engines cooling jackets and heat exchangers etc.
ECOBEAM XL SYSTEMS are designed to
substantially reduce or eliminate paraffin, scale, asphalting, and many other
forms of contaminations from plating out in the pipes and equipment.
PARAFFIN AND THE EFFECTIVE USE OF
THE ECOBEAM XL MHD SYSTEMS
THE APPLICATION
Considerer Paraffin and Scale: THE
ECOBEAM XL MHD SYSTEMS, (including an electromotive force caused by the tools
used) act as a catalyst for the precipitation of ions within the oil flow,
causing irregular crystal structure formation, close to a submicroscopic level.
The minute crystal particles all remain in suspension; they will not form into a
larger solid mass. All remaining fluid is more solvent than that of normal
fluid composition from the well.
Asphaltenes, which are not actually
crystals, normally form as a conglomeration of charge fed particles, there are
attracted, unlike charged molecules. EMF technology affects the surface
charges on these groups of molecules, polarizing them, so that they are
like-charged and resistant, rather than attracted to each other.
The concept that an EMF will interact with crystallization nuclei, explains most
of the phenomenon observed in crude oil with water. Many samples of crude
oil, before and after an EMF treatment, show significant changes in viscosity,
cloud and pour points and temperature deposition of paraffin.
ECOTECH utilizes the highest quality
of materials, which have a very high “intrinsic coercive force”, or resistance
to demagnetization forces. Most external influences have virtually no
degaussing effect on the EMF system. Consistency of the paraffin in a
well, changes from a solid to very light paraffin, which sloughs off with a
forced fluid. Prior to the EMF exposure, the precipitate of calcium
carbonate contained calcite and aragonite in about a 4:1 ratio. Following
installation of an EMF system, the ratio is about 1:4. It is one of the
fundamental laws of physics, that the motion of a conductor through a magnetic
field (EMF) will cause a voltage to be produced.
GROUND WATER RECOVERY
APPLICATION
ECOTECH ventured to apply its Cutting Edge technology, when the discovery of oil
leakage into ground began to cause very serious problems. Oil and Chemical
leakage from Oil storage and oil and chemical wash facilities seriously
contaminate the ground water. It is then required by law, that the
owner/operator of the facility recover the Ground water. This involves the
pumping up of the water, remediation and injection back into the ground. This
process caused serious calcification and deposits of other contaminants in the
piping systems, holding tanks and at the stripping towers. The application of
the ECOBEAM XL SYSTEMS, obviate most of the problems and assist in the overall
efficiency of the process. The potential opportunity is at fuel and oil storage
facilities and at gasoline station sites. When it has been determined that
the ground water (aquifer) has been contaminated by leakage from above, or
around underground storage tanks (UST) the water must be clarified before it
contaminates the whole aquifer.
Common practice is to drill wells on
the property or to contact the water table. This could mean numerous
wells. A submersible pump is then put into each well to pump the
contaminated water to the surface. The installation of the ECOBEAM XL
SYSTEMS at strategic locations will greatly enhance the overall operation of the
Ground Water Recovery operation.
The water enters a series of
filters, before being pumped to a Stripping Tower from the top. It then cascades
and descends through a loose filter media. Semi-filtered water collects in
the sumps of the Stripping Tower. The water is pumped from the sump to the
ground, usually through a filter bed. Most of the times, the problem area is the
pipe from the tower sump to the filter and the pipe back to the aquifer. A heavy
scale builds up and in some instances, forms heavy rust.
The preferred location for the
installation of the ECOBEAM XL SYSTEMS is carefully chosen after the pump
discharge from the sump. Without the ECOBEAM XL SYSTEMS, the carbon
filters tanks that cost from $10,000.00 and up need to be replaced within a
year. With our system these carbon filter tanks could last for many years.
Consideration should also be given
to installing an array of ECOBEAM XL SYSTEMS on the pipe from the well to the
stripping tower, to prevent any scale formation throughout the tower.
PROBLEMS
FACED TODAY
ECOTECH INTERNATIONAL, INC. strives to enhance the quality of the world’s most
important natural resource: WATER.
Although two thirds of the surface of the earth is covered with water, only 3%
of the entire available moisture on our planet is drinkable. This precious life
sustaining resource is fast depleting, with the reckless use of and the
continuous infusion of hazardous chemicals into our ground, surface, and
atmospheric water. These and other contaminants and dissolved solids in the
water negatively affect all domestic, recreational, agricultural and industrial
water sources. As a consequence, we are now faced with very serious health
problems to human, animal, sea, and plant life. To address this situation,
billions of dollars are spent on the chemical treatment and intensive
maintenance of water. The sad thing is that, even in the effort to remedy this
situation, more and more chemicals are being pumped into the water, making an
already bad situation, worse.
Through the application of the Science of Magneto Hydro-Dynamics (MHD), ECOTECH
INTERNATIONAL INC. provides Non Chemical Treatment and Conditioning of Water,
other fluids, and their operating systems. This MHD system is non invasive and
requires absolutely no chemicals, no energy or power. It is maintenance free and
drastically reduces recurring costs, while having a very long, and as yet,
undetermined operating life.
Present
Situation
WATER HAS
JUST THREE BASIC PROBLEMS
a.
Suspended Solids
b.
Bacterial Contamination
c.
Dissolved Solids
SUSPENDED SOLIDS
Suspended
solids are those materials, organic as well as inorganic, that can easily
dissolve into water and can be seen by the naked eye. For example, dust,
suspended materials, rust and so on.
In reality,
this problem is easily solved by one of the many employed techniques. However
the most common are:
(i)
Filtration
(ii)
Flocculation
(iii)
Precipitation
Consequently,
while it is the most common occurrence, suspended solids in water is not really
a big problem. Even in far flung areas of the world, people use layers of cloth
or even a batch of fresh leaves or fresh grass to be rid of the most apparent
dissolved solids.
BACTERIAL CONTAMINATION
There are
many kinds of bacteria that can find a home in water. Some of these bacteria can
withstand extreme heat and can go into suspended animation when frozen.
Therefore the idea that boiling water will kill bacteria is a misnomer. Freezing
will not help either, because there is scientific evidence that bacteria has
survived in near absolute zero conditions for millions of years. Therefore the
belief that freezing anything will keep it bacteria free is also misplaced.
Such bacteria
have to be destructed by repeated evaporation, or by using Advanced Oxidation
Techniques. Repeated evaporation is employed in the DISTILLATION process in the
effort to acquire pharmaceutical grades of ultra pure water. It is very
expensive and extraordinary precautions must be taken to keep the derived water
free of bacteria.
Advanced
Oxidation Techniques involve the use of highly specialized equipment which
itself can cost between half a million to several million dollars.
However,
there is one thing that no bacteria can negotiate. All living organisms have a
brain function. All brains have electrical activity. All electivity is subject
to the Laws of Physics. Our Invention, the “ECOBEAM XL SERIES OF MHD
SYSTEMS” SATISFIES THE LAWS OF PHYSICS TO A DEGREE THAT THESE LAWS CAN BE
APPLIED TO ANY ELECTRICAL PHENOMENON.
CONSEQUENTLY,
NO MATTER THAT THE STRAIN OF BACTERIA, OUR ECOBEAM XL SYSTRM WILL PARALIZE THE
BRAIN ACTIVITY OF THE STRONGEST STRAIN OF BACTERIA IN THE WATER, OR ANY OTHER
MEDIUM THAT PASSES ACROSS IT.
Therefore,
the two problems with water, i.e.: suspended solids and bacteria are NOT really
big problems, because existing technologies can easily address them.
DISSOLVED SOLIDS
This is the
biggest and by far the most difficult problem to solve in water.
Dissolved
solids cause TWO problems in water.
(i)
Temporary Hardness
(ii)
Permanent Hardness
This is the
phenomenon, whereby materials completely dissolve into the water to a degree
where they are not visible, unless examined by a powerful microscope. For
example; consider the disappearance of salt and calcium into the water. To the
eye, the water will look clean and pure. But under the microscope, the water
contains hundreds if not thousands of dissolved materials. The presence of these
materials in the dissolved state, render the water to be hard. The degrees of
hardness are explained below.
TEMPORARY HARDNESS IN WATER
This is
caused by substances that when in contact with water in motion, will easily
break up into microscopic particles and easily homogenize with the water. Thus
they disappear into the water, just like salt would when stirred into the water.
That is a dissolved solid that causes temporary hardness. This temporary
hardness is determined by the number of molecules of the water surrounding each
molecule of the dissolved substance. If the water bond in this
relationship can be easily disturbed, then the hardness is temporary. Most of
the time, the problem of temporary hardness is addressed by adding chemicals
into the water.
While this is
NOT a solution, it does bring the water to a state where industry can achieve an
end. However, the addition of chemicals into water can only make the end state
of that water worse than it was to begin with. But since the chemical industries
sell over TEN BILLION DOLLARS worth of chemicals to the water industry every
year, alternative safer remedies are discouraged and suppressed.
PERMAMENT HARDNESS IN WATER
This is a
phenomenon where the dissolved solid breaks into such microscopic particles that
one such particle is encapsulated within between 330 (three hundred thirty) to
360 (three hundred sixty) molecules of the hydrogen bond of the water.
This bond is very strong, and cannot be broken by chemicals. Thus it is called
THE PERMANENT HARDNESS OF WATER. This situation has opened a new science in
water called the: “CLUSTER THEORY OF WATER.” While American scientists have not
paid much attention to this phenomenon, the Japanese have done advanced research
on the subject.
Up until now,
science has had little to say about the PERMANENT HARDNESS OF WATER.
However, in the laboratory, our ECOBEAM XL SYSTEMS have broken this super strong
hydrogen bond, releasing the encapsulated dissolved solid. The details of this
bond and the effect on our ECOBEAM XL TECHNOLOGY on it is available on our web
page:
www.ecotechintlinc.com
UNIVERSAL SOLUTION
At the
moment, present Science has just TWO ways of dealing with DISSOLVED SOLIDS.
(i)
Distillation
(ii)
Reverse Osmosis
DISTILLATION
This is a process whereby water is boiled and evaporated and the steam condensed
back to water. The systems require the use of specialized vessels, a huge amount
of thermal energy (which itself is not environment friendly). A great amount of
monitoring and specialized storage facilities. It is a very expensive process.
At the end of it all, the water is NOT fit for human consumption and
electrolytes must be added to render it fit for such.
REVERSE
OSMOSIS
While this is the most effective and most widely used system in the world, it is
very expensive to operate.
All of the equipment used must be at least 316L stainless steel. Very high
pressure stainless steel pumps are used to force the water through specialized
membrane houses in the stainless steel tubes. The systems require huge amounts
of energy and round the clock monitoring. The systems must be shut down and the
membranes must be replaced regularly. Even then, the average “reject water” from
the reverse osmosis system is still anywhere between 30-90%.
Admittedly, this is the most widely used system in the world, but it is also the
most expensive.
ECOTECH INTERNATIONAL INC. has come up with a THIRD solution to this problem.
ECOTECH INTERNATIONAL INC applies the Laws of Physics to the Chemistry of the
Water, Fluid or Gas in such a way, that the DISSOLVED SOLIDS go into Suspension.
In other words, the ECOBEAM XL TECHNOLOGY, converts our problem number three
(dissolved solids) and changes them into problem number one (suspended solids
which are easily removed from the water as explained above).
The ECOBEAM XL SERIES OF SYSTEMS does this without the use of chemicals or any
form of energy.
THUS WE HAVE
SOLVED THE GREATEST PROBLEM WITH WATER.
VISION
TO PROVIDE OUR WORLD WITH THE GIFT OF “LIVING
WATERS!”
When God provided this earth water, it was so pristine, that we could go to any
source, surface, mountain springs, rivers or aquifers, and we could drink from
them without worry. Today even though two thirds of the surface of the
earth is covered with water, less than 3% of all that available water is
drinkable. The rest has been contaminated with the “discriminate” and more
importantly the “indiscriminate” use of chemicals and fossil fuels.
The sad thing is that out of this desperate situation has grown an industry in
water treatment plants and water bottling plants that have added to the burden
on the poor thirsty man. Most of the situations are being addressed by the
excessive use of additional chemicals, which only worsen the situation, because
they are using the very same chemicals that caused the water to become polluted
in the first place.
The ECOBEAM XL SERIES OF MHD SYSTEMS can be used in conjunction with existing
protocols to greatly reduce the burden of chemicals in the water. It is our hope
that we can find the following two expedients so essential to making our God
given gift of water, pristine again.
(i)
Finances to produce the equipment on a financially viable scale.
(ii)
Marketing expertise.
There is not doubt that if handled properly, the technology that has been
invented can become bigger than MICROSOFT. The reasoning is simple.
Most humans, all animals and vegetation have flourished for thousands of years
without computers, BUT NOT A SINGLE ORGANISM CAN SURVIVE WITHOUT WATER.
Today over ninety seven percent of all available water is highly contaminated.
The only known technologies in the world being practiced use additional chemical
to address the situation already created by the use of chemicals.
It is our belief, that at the moment, WE HAVE THE ONLY TECHNOLOGY IN THE WORLD,
THAT CAN ADDRESS THE PROBLEMS WITH WATER WITHOUT THE USE OF ENERGY AND REDUCE
OUR DEPENDENCE ON HARMFUL CHEMICALS
OBJECTIVE
Our
objectives are as follows:
a.
Seek
funding
b.
Seek
effective marketing (SOLVED AS OF JUNE 5, 2005)
FUNDING
When we
receive the funds, we would do the following.
Phase One:
(i)
Produce the ECOBEAM XL SERIES OF MHD UNITS in bulk thereby reducing cost.
(ii)
Produce the Housing mechanism for installing the ECOBEAM XL UNITS WHERE
REQUIRED, so as to protect them not only from the elements, but also from
thieves.
(iii)
Build
specialty hermetically sealed ECOBEAM XL SUPER AND ECOBEAM XL JUMBO UNITS for
installation on Oil Pipe lines and Underground water migration Pipe lines.
(iv)
Produce at least TEN FULLY SELF CONTAINED, PORTABLE SKID MOUNTED WATER
TREATMENT PLANTS FOR THE TSUNAMI AFFECTED AREAS. Each plant will produce a
minimum of FIFTY THOUSAND GALLONS OF CLEAN FRESH DRINKING WATER EVERY TWENTY
FOUR HOURS.
(v)
Secure
an assurance that when these plants prove their worth, assistance will be
available to manufacture more of these plants in areas where cost of labor can
be reduced.
(vi)
Eventually such water treatments plants can be manufactured to produce as
little as one thousand to one million gallons of water per day. If more water is
required, the plants can be placed side by side to produce the required amount
of water.
Phase Two
Integrated
Filtration Systems for:
a. Individual
home use with state of the art self monitoring.
b. Single
systems for use in a building with state of the art self monitoring.
c. Single
systems for use in a cluster of buildings with state of the art self-monitoring.
d. Single systems for use in villages with state of the art self monitoring.
e. Single systems for use in small towns with state of the art self monitoring.
f. Augment
existing water treatment plants wherever they are operating at the moment.
Phase Three
Produce a
complete line of WATER TREATMENT SYSTEMS OF THE HIGHEST POSSIBLE QUALITY and
make them available at costs less than the market value. This would include:
a.
A
complete line of filters from four inches in length to four feet in length
covering from 5 micron to 0.001 micron.
b.
A
complete line of housing units for these filters.
c.
A
complete line of hot and cold water dispensing systems for home and office use.
Every such system, whether for an individual home or an office, would have the
ECOBEAM XL technology integral to them and would have state of the art self
monitoring.
All of this can be done quite easily and with capitol requirements that are not
very high, because once started the turn over from the market would replenish
the coffers for further investments in improvements.
Capital
Requirements
Before we even touch upon the subject of FUNDING; there are very pertinent
questions that must be asked.
Why should anyone bother with ECOTECH INTERNATIONAL INC, when there are
thousands of companies around the world that have been engaged in the water
business for many years? Some of these companies are so huge that their
operating capital runs into the billions of dollars.
These being the case, why even bother with ECOTECH INTERNATIONAL INC?
The
answers are simple.
a.
These
water companies have been in business for decades for just that: BUSINESS. They
make it possible for the chemical industry to sell over ten billion dollars
worth of chemicals which are dumped into the water every year. Therefore while
they do engage in wonderful and indispensable work, with every heart beat, the
situation of our water gets worse with the addition of more and more toxic
additives.
b.
Visualize this: If nobody ever got sick, would not the doctors, the hospitals
and the entire pharmaceutical industry close? Is it not a fact that the lively
hood of all of the mentioned depends upon people getting sick? Or if a car never
developed any trouble, what would the auto mechanics do for a living? Similarly,
if water did not have any problems and was as good as God had made it, what
effect would that have on the industry that thrives on the water being bad?
c.
Every
single WATER TREATMENT COMPANY IN THE WORLD relies very heavily on the addition
of chemicals to treat water. While some chemical protocols are absolutely
necessary because of the severity of the contaminants, there are a lot of
chemicals that can be reduced and eventually completely eliminated, but this too
would be acceptable, because it would reduce the sale of chemicals to the water
industry.
d.
ECOTECH INTERNATIONAL INC has introduced a new paradigm to this seemingly
hopeless situation. The ECOBEAM XL MHD SYSTEMS have a ONE HUNDRED PERCENT proven
track record of ONE HUNDRED PERCENT SUCCESS in ever single application in twenty
six countries. Therefore, the ECOBEAM XL MHD SYSTEMS, by themselves, or in
conjunction with existing protocols, is the only NON CHEMICAL SOLUTION to the
treatment and conditioning of water in the world. Our applications are installed
on a variety of usages from industrial, domestic, municipal or any other
protocol where water or fuel is required.
e.
The
hope of reduction of chemicals in our water is reason enough to look to the
future.
The backbone of the technology is the ECOBEAM XL SERIES OF MAGNETO
HYDRO-DYNAMICS PRODUCTS. Up until now, every single module has been carefully
assembled by hand. We desire to continue to do so, so as to ensure absolute
perfection in our work. We have designed a machine that can be used for
automation, but the cost of producing just one machine, seven years ago, ran
over FIFTY THOUSAND DOLLARS. The machine can be modified to assemble all of the
different units of the ECOBEAM XL FAMILY. However prudence dictates that we have
at least three such machines. Today’s cost will most certainly be higher.
Consequently, for the time being, we are content to assemble each unit by hand.
All of the assembly work is performed by the AMISH on their farms. They are very
well trained and have withstood the very stringent standards of perfection
demanded by the Japanese.
The manufacture of the housing mechanism would continue to be outsourced. We are
currently using anodized stainless steel GUN METAL for the fabrication of these
housings. This is important because when exposed to the elements, for ten to
twenty years or more, we do not want the material to degrade because of the
elements. We can manufacture these housings, as we have done up until now at one
third the cost of the same in the USA.
Each ECOBEAM XL Installation must be carefully encapsulated and sealed. This is
done with Aluminum casings indoors where atmospheric conditions permit, and with
our specially coated materials when exposed to the outside elements. This too is
out-sourced for cost reduction.
The
construction of the Water Treatment Plants is undertaken in the following way.
(i)
We
take the requirements of the end user.
(ii)
We
then acquire at least 3 years of data (when possible) on the water analysis of
the area where this plant is required. The study of this data, gives us a broad
base about the condition of the water. We then take the worst case scenario of
the water and add an element of further disaster to deal with a possible
worsening situation. This then becomes the base line for the Water Treatment
Protocols that we must design the equipment for.
(iii)
We
then go to the open market and select the BEST EQUIPMENT AVAILABLE IN THE WORLD
FOR THE BASE LINE THAT WE HAVE ESTABLISHED.
(iv)
We
demand from the manufacturers of the equipment full technical support and
warranties, both in the USA and through their regional offices world wide.
(v)
All
ancillary equipment is similarly bought and brought to our assembly area.
(vi)
We
have engineers who are experts in water technology, civil engineering,
architecture, and technicians who are experts in welding and assembly. They have
come together as a team to assemble the equipment.
(vii)
Integral to the assembly of the plant, is the precise installation of the
ECOBEAM XL MHD SYSTEMS at precise NODAL points. The entire equipment is them
tested at conditions that are harsher than those anticipated.
(viii)
Only then is the equipment ready for handing over to the end user.
(ix)
We
demand to be awarded a THREE YEAR MONITORING CONTRACT on each piece of our
equipment. This ensures that the equipment is functioning perfectly, that no
sabotage occurs and that the end user can be fully trained on its use and
minimal maintenance.
On the world market, a similar SKID MOUNTED Water Treatment Plant, producing
about fifty thousand gallons of water per day, would be available for between
three to four hundred thousand US dollars. ECOTECH INTERNATIONAL INC will not
only integrate the ECOBEAM XL TECHNOLOGY into the plant but could produce it for
around two hundred fifty thousand dollars, saving more money for the end user.
The details of the costs will vary with market conditions and equipment acquired
in bulk. But we can certainly produce world class equipment at a lesser cost.
With good marketing to a world hungry for clean water, we could sell thousands
of these plants at prices that are attractive to the consumer, and recover all
of our investment in a matter of months.
In Asia alone, there are OVER THREE AND A HALF BILLION PEOPLE LOOKING FOR CLEAN,
GREAT TASTING, PURE WATER.
Municipal Water Treatment Enhancement
Solar Powered Desalination Plant
Drinkable water plant from storm water
in remote
area in Thailand
Page
1
Page 3
